Inverter Wiring Connection: इन्वर्टर का कनेक्शन पूरे घर में कैसे दें? डायग्राम सहित (2026 Mega Guide)
क्या आप नया इन्वर्टर (Inverter) लाये हैं और इलेक्ट्रीशियन (Electrician) बुलाने का खर्च बचाना चाहते हैं? या फिर आप एक इलेक्ट्रीशियन हैं और किसी बड़े घर की वायरिंग को प्रोफेशनली डिज़ाइन करना चाहते हैं? भारत में घरों के अंदर इन्वर्टर की वायरिंग करना कोई रॉकेट साइंस नहीं है, लेकिन अगर एक तार भी गलत जुड़ जाए, तो आपका नया इन्वर्टर तुरंत जल सकता है (Short Circuit)।
भारत में 95% घरों में "Single Wire Inverter Connection" (सिंगल वायर इन्वर्टर कनेक्शन) का इस्तेमाल होता है। इसका मतलब है कि इन्वर्टर से सिर्फ एक तार (Phase) निकलकर आपके घर के स्विच बोर्ड्स तक जाता है। न्यूट्रल (Neutral) का तार घर की सरकारी बिजली की लाइन (Grid) से ही कॉमन (Common) ले लिया जाता है।
इस डीप-टेक गाइड में, हम आपको न केवल तार जोड़ना सिखाएंगे, बल्कि यह भी बताएंगे कि किसी भी घर की वायरिंग करने से पहले उसका Single Line Diagram (SLD) कैसे तैयार करें, ताकि भविष्य में कोई फॉल्ट (Fault) ढूँढने में परेशानी न हो।
विषय-सूची (Table of Contents)
- 1. प्रो टिप: वायरिंग से पहले SLD (Single Line Diagram) बनाएं
- 2. वायरिंग के लिए ज़रूरी सामान और तार की मोटाई (Gauge)
- 3. स्टेप 1: इन्वर्टर को बैटरी से कैसे जोड़ें?
- 4. स्टेप 2: सिंगल वायर कनेक्शन (Single Wire Concept)
- 5. स्टेप 3: स्विच बोर्ड के अंदर इन्वर्टर का तार कैसे लगाएं?
- 6. 3 भयंकर गलतियाँ जो इन्वर्टर जला सकती हैं
- 7. अक्सर पूछे जाने वाले प्रश्न (FAQs)
1. प्रो टिप: वायरिंग से पहले SLD (Single Line Diagram) बनाएं
एक प्रोफेशनल इंजीनियर कभी भी सीधा तार नहीं काटता। वह सबसे पहले एक Single Line Diagram (SLD) बनाता है। SLD एक ब्लूप्रिंट या नक्शा है जो यह तय करता है कि कौन सा उपकरण (Appliance) इन्वर्टर पर चलेगा और कौन सा सरकारी ग्रिड पर।
इन्वर्टर लोड (Inverter Load): हर कमरे में 1 पंखा, 2 ट्यूबलाइट, Wi-Fi राउटर, और टीवी। इन उपकरणों के स्विच को हम 'इन्वर्टर फेज़' (Inverter Phase) से जोड़ेंगे।
ग्रिड लोड (Grid Load/Heavy Load): AC (एयर कंडीशनर), गीजर (Geyser), हीटर, पानी की मोटर (Water Pump), और 15A के पावर सॉकेट। इन्हें इन्वर्टर से बिल्कुल अलग रखेंगे और सीधे सरकारी 'मेन फेज़' (Grid Phase) से जोड़ेंगे।
2. वायरिंग के लिए ज़रूरी सामान और तार की मोटाई (Gauge)
इन्वर्टर वायरिंग के लिए आपको इन चीज़ों की ज़रूरत पड़ेगी:
- इन्वर्टर वायर (Inverter Wire): इन्वर्टर से स्विच बोर्ड तक जाने वाला तार कम से कम 1.5 sq.mm (कॉपर) का होना चाहिए। रंग (Color) हमेशा पीला (Yellow) या सफ़ेद (White) चुनें ताकि वह लाल (Main Phase) और काले (Neutral) तारों से अलग दिखे।
- Line Tester (टेस्टर): करंट चेक करने के लिए।
- Wire Stripper (वायर स्ट्रिपर) & Plier (प्लास): तार छीलने और कसने के लिए।
- Insulation Tape (टेप): तारों को सुरक्षित करने के लिए।
3. स्टेप 1: इन्वर्टर को बैटरी से कैसे जोड़ें?
सबसे पहले सुरक्षा (Safety)! इन्वर्टर का मेन प्लग (Mains) दीवार में नहीं लगा होना चाहिए और इन्वर्टर का फ्रंट स्विच OFF होना चाहिए।
- इन्वर्टर के पीछे से दो मोटे तार निकलते हैं: एक लाल (Red) और एक काला (Black)।
- लाल तार (Positive) को बैटरी के प्लस (+) टर्मिनल (लाल रंग) पर कस दें।
- काले तार (Negative) को बैटरी के माइनस (-) टर्मिनल (काले रंग) पर कस दें। (यहाँ हल्की चिंगारी/Spark आ सकती है, यह नॉर्मल है)।
- रेंच (Spanner) से नट-बोल्ट को बहुत टाइट कसें। ढीला छोड़ने पर टर्मिनल पिघल सकता है।
4. स्टेप 2: सिंगल वायर कनेक्शन (Single Wire Concept)
अब इन्वर्टर से घर के अंदर करंट कैसे जाएगा? इसके लिए इन्वर्टर के पीछे एक 3-पिन आउटपुट सॉकेट (3-Pin Output Socket) होता है।
- इन्वर्टर का फ्रंट बटन ON करें (अभी मेन सप्लाई बंद रखें)।
- अपना 'टेस्टर' लें और इन्वर्टर के पीछे वाले 3-पिन सॉकेट के दाईं तरफ (Right side / Line) वाले छेद में डालें। टेस्टर जलना चाहिए।
- यही आपका "Inverter Phase" है।
- अब एक 3-पिन प्लग लें (या सीधा तार डालें) और उस तार को इस दाईं तरफ (Right/Phase) वाले पिन से जोड़ दें। यही एक 1.5 sq.mm का तार (मान लीजिए पीला तार) अब आपके पूरे घर के स्विच बोर्ड्स तक जाएगा।
(नोट: हमें इन्वर्टर से न्यूट्रल (Neutral) ले जाने की ज़रूरत नहीं है, क्योंकि पूरे घर की न्यूट्रल लाइन आपस में जुड़ी होती है और वह सरकारी बिजली से 'कॉमन' रहती है।)
5. स्टेप 3: स्विच बोर्ड के अंदर इन्वर्टर का तार कैसे लगाएं?
यही वह जगह है जहाँ सारा डिज़ाइन (SLD) काम आता है।
- कमरे का स्विच बोर्ड खोलें। आपको दिखेगा कि सभी स्विच के नीचे वाले हिस्से एक लाल तार (Main Grid Phase) से आपस में जुड़े (Loop) हुए हैं।
- मान लीजिए आप 1 पंखा और 1 लाइट इन्वर्टर पर करना चाहते हैं।
- उन दो स्विच (पंखा और लाइट) के नीचे से वह लाल तार (Main Phase) काट कर अलग कर दें।
- अब उन दोनों स्विच के नीचे वाले टर्मिनल पर इन्वर्टर का पीला तार (Inverter Phase) जोड़ दें।
- ध्यान दें: लाल तार (सरकारी बिजली) और पीला तार (इन्वर्टर बिजली) कभी भी आपस में नहीं जुड़ने चाहिए (Never Mix Phase)। इन्हें पूरी तरह अलग (Isolate) रखना है।
- बोर्ड बंद कर दें।
अब मेन MCB चालू करें और इन्वर्टर को दीवार के सॉकेट में प्लग करके उसकी चार्जिंग चालू कर दें। आपका सिस्टम तैयार है!
6. 3 भयंकर गलतियाँ जो इन्वर्टर जला सकती हैं
वायरिंग करते समय इन 3 गलतियों से बचें:
- Phase Mix (फेज़ मिक्सिंग): अगर स्विच बोर्ड में आपने मेन ग्रिड का फेज़ (लाल तार) और इन्वर्टर का फेज़ (पीला तार) एक ही स्विच में जोड़ दिया, तो जैसे ही लाइट आएगी, आपके इन्वर्टर का मदरबोर्ड (PCB) तुरंत जलकर राख हो जाएगा।
- Reverse Polarity (उल्टे तार): अगर बैटरी का लाल तार इन्वर्टर के काले तार से जोड़ दिया, तो इन्वर्टर के DC फ्यूज़ तुरंत उड़ जाएंगे।
- Neutral Wiring Error: इन्वर्टर के पीछे के 3-पिन प्लग में कभी भी न्यूट्रल (Neutral) वायर कनेक्ट करके घर में न भेजें। सिंगल वायर सिस्टम में न्यूट्रल हमेशा ग्रिड का ही इस्तेमाल होता है।
7. अक्सर पूछे जाने वाले प्रश्न (FAQs)
Q1. क्या मैं 1mm के तार से इन्वर्टर की वायरिंग कर सकता हूँ?
अगर आपके घर का लोड बहुत कम है (सिर्फ 2 पंखे और कुछ लाइट्स), तो 1.0 sq.mm का तार चल जाएगा। लेकिन भविष्य की सुरक्षा और हैवी लोड (जैसे मिक्सी या प्रेस) के लिए हमेशा 1.5 sq.mm कॉपर वायर का इस्तेमाल करना सबसे अच्छा होता है।
Q2. लाइट जाने पर इन्वर्टर पर रखे पंखे धीरे क्यों चलते हैं?
अगर आपका इन्वर्टर "Square Wave" (स्क्वायर वेव) है, तो लाइट जाने पर पंखों से 'हम्मिंग' (गूंजने) की आवाज़ आएगी और वे थोड़े धीरे चलेंगे। हमेशा "Pure Sine Wave" (प्योर साइन वेव) इन्वर्टर खरीदें, जो ग्रिड जैसी ही साफ बिजली देता है।
Q3. इन्वर्टर से करंट (Shock) लग रहा है, क्या करूँ?
यह 'अर्थिंग' (Earthing) की समस्या है। इन्वर्टर के पीछे एक अर्थिंग का पेंच होता है। उसे घर की अर्थिंग वायर (हरे रंग की तार) से जोड़ दें। इन्वर्टर की बॉडी में आ रहा लीकेज करंट सीधा ज़मीन में चला जाएगा।
Inverter Wiring Connection: How to Wire Your Entire Home? With SLD & Diagram (2026 Mega Guide)
Did you just purchase a new home inverter and want to save money on hiring an electrician? Or are you an electrical enthusiast wanting to design a professional wiring layout for a large house? Wiring an inverter in an Indian household is not rocket science, but making even a single misstep—like crossing the wrong wires—can instantly fry your brand-new inverter (Short Circuit) and void its warranty.
In over 95% of Indian homes, the "Single Wire Inverter Connection" is the standard practice. This means only one wire (the Phase) travels from the output of your inverter to the switchboards across your house. The Neutral wire is cleverly kept "Common" with the government grid supply.
In this deep-tech commercial guide, we will not only teach you how to strip and screw wires, but we will also introduce you to the professional engineering concept of drafting a Single Line Diagram (SLD) before touching any wires. This ensures fault-free load distribution and absolute safety.
Table of Contents
- 1. Pro Tip: Draft a Single Line Diagram (SLD) Before Wiring
- 2. Essential Tools and Correct Wire Gauge
- 3. Step 1: Connecting the Inverter to the Battery
- 4. Step 2: The Single Wire Output Concept
- 5. Step 3: Wiring Inside the Room's Switchboard
- 6. 3 Disastrous Mistakes That Will Fry Your Inverter
- 7. Frequently Asked Questions (FAQs)
1. Pro Tip: Draft a Single Line Diagram (SLD) Before Wiring
A professional electrical engineer never blindly cuts a wire. The very first step is to draft a Single Line Diagram (SLD). An SLD is a blueprint that dictates exactly which appliances will run on battery backup (Inverter Load) and which will remain exclusively on the government supply (Grid Load).
Inverter Load: 1 Ceiling Fan, 2 LED Tubes, Wi-Fi Router, and TV per room. The switches for these appliances will be connected to the 'Inverter Phase'.
Grid Load (Heavy Load): Air Conditioners (AC), Geysers, Heaters, 1HP Water Pumps, and heavy 15A Power Sockets. These must be completely isolated from the inverter and connected directly to the 'Main Grid Phase'.
2. Essential Tools and Correct Wire Gauge
To execute the inverter wiring flawlessly, gather the following inventory:
- Inverter Wire: The single wire running from the inverter to the switchboards must be at least 1.5 sq.mm thick (Pure Copper). Always choose a distinct color like Yellow or White so it stands out easily against the Red (Grid Phase) and Black (Neutral) wires.
- Line Tester (Phase Tester): To safely detect live current.
- Wire Stripper & Pliers: For cleanly cutting, stripping, and twisting copper strands.
- Insulation Tape: High-quality PVC tape to secure exposed joints.
3. Step 1: Connecting the Inverter to the Battery
Safety absolute first! Ensure the inverter's main power cord is unplugged from the wall socket and the front power switch is turned OFF.
- Identify the two thick DC cables coming out from the back of your inverter: One is Red (Positive) and the other is Black (Negative).
- Bolt the Red cable to the Positive (+) terminal (painted Red) of the battery.
- Bolt the Black cable to the Negative (-) terminal (painted Black) of the battery. (You may see a tiny, harmless spark here; do not panic, it's normal capacitor charging).
- Use a spanner to tighten the nut-bolts exceptionally well. A loose connection will melt the lead terminal due to high DC resistance.
4. Step 2: The Single Wire Output Concept
How does the power travel from the inverter to the house? Look at the back of the inverter; you will find a 3-Pin Output Socket.
- Turn the front button of the inverter ON (Keep wall mains OFF).
- Take your 'Line Tester' and insert it into the Right-side hole (Line/Phase) of that 3-pin socket. The tester's neon bulb should glow.
- This right-side pin is your "Inverter Phase".
- Take a 3-pin plug, connect your 1.5 sq.mm Yellow wire strictly to the Right-side pin of the plug, and insert it into the inverter. This single Yellow wire will now run across your house into every switchboard.
(Note: We do not extract a Neutral wire from the inverter. In Indian homes, the entire neutral circuit is interconnected and remains "Common" with the grid supply.)
5. Step 3: Wiring Inside the Room's Switchboard
This is where your SLD (Single Line Diagram) blueprint comes to life.
- Unscrew and open the room's switchboard. You will notice a thick Red wire (Main Grid Phase) looping and connecting the bottom terminals of all the switches together.
- Identify the switches for the appliances you want on the inverter (e.g., 1 Fan and 1 Light).
- Cut and remove the Red wire (Main Phase) looping across the bottom of those two specific switches.
- Now, strip your Yellow wire (Inverter Phase) and connect it to the bottom terminals of those two switches.
- Golden Rule: The Red wire (Grid Phase) and the Yellow wire (Inverter Phase) must NEVER touch or mix (Never Mix Phase). They must be 100% isolated from each other.
- Screw the switchboard back onto the wall.
Finally, turn ON the Main MCB, and plug the inverter's main charging cord into the wall socket. Your automated backup system is successfully deployed!
6. 3 Disastrous Mistakes That Will Fry Your Inverter
Avoid these catastrophic errors at all costs during installation:
- Phase Mixing (The Ultimate Destroyer): If you mistakenly connect both the Grid Phase (Red) and Inverter Phase (Yellow) to the same switch terminal, the moment grid power returns, high voltage will shoot back into the inverter, instantly incinerating its internal PCB motherboard.
- Reverse Polarity: If you connect the battery's Red terminal to the inverter's Black wire, the massive DC short circuit will instantly blow the internal DC fuses of the inverter.
- Neutral Wiring Error: Never wire a Neutral line into the 3-pin output plug of the inverter and send it into the house. A single wire system inherently utilizes the grid's common neutral.
7. Frequently Asked Questions (FAQs)
Q1. Can I use a thinner 1.0 sq.mm wire for inverter wiring?
If your total load is exceedingly light (just 2 fans and LED bulbs), a 1.0 sq.mm wire will technically work. However, for long-term safety, voltage stability, and future-proofing against heavier loads (like a mixer grinder or TV), standard engineering codes highly recommend a 1.5 sq.mm multi-strand copper wire.
Q2. Why do my ceiling fans make a humming noise when running on the inverter?
If you purchased a cheaper "Square Wave" inverter, the choppy electrical waveform causes magnetic resonance in inductive loads like fans, resulting in a buzzing noise and slower speeds. Always invest in a "Pure Sine Wave" inverter, which perfectly mimics clean grid electricity.
Q3. I am getting mild electric shocks from the inverter's metal body. What should I do?
This is a classic 'Earthing' (Grounding) issue. Look at the back of the inverter chassis; there is a dedicated earthing screw. Connect a green wire from that screw directly to your home's main Earthing line. Any leakage current will safely bypass you and go directly into the ground.
